Bed: The flat bed is
one piece supporting the headstock and carriage. The casting
is poured in our own foundry to DIN 1691 standards. Our
foundry is ISO 9002 certified and has been since 1994.
The bed casting is heavily ribbed and provides excellent
vibration dampening.
Guide
ways: Guide
ways are hardened and ground for maximum precision and
long life. The Z-axis moves on the bed which has a vee
and a rectangular way. .063” Turcite on the underside
of the carriage ensures minimum friction and long life.
The cross slide guide ways are a precision ground system
with one gib on the side away from the headstock.
Headstock: Driven by
an AC motor and connected using a poly-V belt, speeds are
continuously variable. The Romi spindle uses ultra precision
bearings which are lubricated for life. Spindle bearings
are P4 (AFBMA-B7) double angular contact ball bearings
in front and SP double-row cylindrical roller bearings
at the rear of the spindle. The high load capacity of the
bearings provides rigidity and superior vibration dampening
under the most severe cutting conditions. Bearings are
fully sealed to prevent contamination from coolant or abrasive
particles.
Ball Screws: Ball screws are manufactured
and ground by Romi where complete control over the accuracy and quality
is assured. We are not dependent on commercially available products.
The double ball nuts are large in width and diameter. The double nut
design provides positive location by mating with both flanks of the
screw at all times. This design also minimizes heat distortion. Thermal
gauging or temperature reduction systems are not required. The X axis
is pre-tensioned using P5 angular contact ball bearings.
Lubrication: Automatic lubrication
with line filtration is standard. The reservoir is located at the tailstock
end of the machine in plain sight and easy to refill. It is protected
from accidental damage. The reservoir has 1/2 gallon capacity.
Guarding: Romi uses 10 gauge, powder
coated steel for all external guarding. No accordion guards are used.
The door is easy to open and close gliding on multiple rollers. The
double overlapping seal ensures that coolant remains in the cutting
area, not on your floor. A large safety window allows the operator
to monitor machine operations.
Centur 30G Bar Turning Center Includes as
standard:
ASA A2-5” spindle nose, with 2.09” (53 mm) diameter through
hole
Continuously variable spindle speed, from 5 to 5,500 rpm
10 HP (7.5 kW) variable speed spindle motor
Pull Back collet chuck using 16C collets hydraulically actuated with
one 16C collet
Centur 30G's include
as standard:
Gang tool system “U” shaped cross slide with “T” slots,
including 1 cut off tool holder, 1 mechanical bar puller with built-in
cut off tool holder, 2 external turning tool holders, 2 boring bar
holders, 1 double boring bar holder and 5 reduction sleeves
Parts catcher 1 5/8” X 4 ¾” capacity
Automatic lubrication system with low level sensor and line filter
Romi ABR-80 bar loader interface
Collet chuck with hydraulic actuation
Modular Bar guide tube
Blind disc kit to be machined as bar guide and support in the spindle
Chip conveyor, hinged belt, transverse mounted, rear exhaust
Coolant system
Electrical system 230 V, 50/60 Hz, 20 KVA
Fully enclosed work area, with interlocked sliding door
GE-Fanuc control Series 0i-T with 9” monitor
Set of leveling screws and nuts
Set of operating, maintenance, programming, installation, parts manuals
and electrical schematics
Set of wrenches for machine operation
Sealed work light
ROMI
Centur 30G-SERIES GE-Fanuc 0i-T Standard Equipment
2nd, 3rd, 4th reference position return
Absolute (G90) / incremental (G91) programming
Addition of custom macro common variables
Alarm display
Background Editing
Canned Cycles (G77, G78, G79)
Canned Cycles for Drilling (G80, G83, G85, G87, G89)
Chuck and tail stock barrier
Constant surface speed control (G96)
Continuous threading (G33)
Coordinate System Shift
Custom Macro B
Data Protection Key for programs, parameters and variables
Diameter/radius programming (x axis)
Direct drawing dimension programming
Direct input of tool offset value measured
Display unit ( 9" monochrome CRT/MDI)
Dry run . Dwell (G04)
Dynamic graphic display
Emergency Stop
Extend Part Program Editing
Feed per minute (G94)/Feed per Revolution (G95)
G code system (A/B/C)
Help functions
Inch/Metric Conversion (G20, G21)
Ladder Screen Visualization
Linear and Circular Interpolation (G01, G02, G03) Machine Lock
Manual Handle Feed
MDI operation
Memory card input/output (for maintenance) Multiple repetitive cycle
Multiple threading (G33)
|
400 registerable
programs
Operating and alarm history display
Operator message history display
Optional block skip
Part Program Storage length = 256 Kbyte (640 m)
Program Load / Save
Program Restart
Programmable Data Input (G10)
Reader/Puncher Interface (RS-232C)
Run Hour, Parts count display and clock Sequence number comparison
and stop
Single block
Stored stroke check 1 / check 2,3 (Parameter, G22, G23)
Sub program call
Tape format for FANUC Series 10/11
Threading retract
Threading, synchronous cutting (G33)
Tool geometry/wear compensation - 64 pairs
Tool Life Management
Tool Nose Radius Compensation (G40, G41, G42)
Workpiece Coordinate System (G54~G59)
Workpiece Coordinate System Preset (G92, G92.1)
|
Romi Centur
30G Bar Turning Center
|
Price On Request |
| X41396 Romi ABR-80 Bar Loader |
Price On Request |
FOB Erlanger, Kentucky
Terms of Payment are 20% with order
Balance due 30 days after shipment
Terms are subject to credit approval by Romi Machine Tools, Ltd.
Click here to review:
ROMI MACHINE TOOLS, LTD.
TERMS AND CONDITIONS OF SALE AND LIMITED WARRANTY
| GE-Fanuc 0i-T S49731 Spindle Orientation & Rigid
Tapping Required for Hex or Square Stock |
Price On Request |
| Optional Equipment |
|
| Part # |
Description |
|
X41730
|
-Automatic Power Off |
|
| X41787 |
-Internal Transformer for 200/210-220/230-240/250V 50/60
Hz 15 KVA |
|
| X41714 |
-Internal Transformer for 200 to 250-380-420/440-460/ 480V,50/60
Hz, 15 KVA. |
|
| X40319 |
-High pressure coolant system 101 PSI, 2.6 GPM, 2 HP |
|
| OPC00761 |
-Extra set of Romi operating, maintenance, installation
and parts manuals |
|
| OPC00762 |
-Canada (includes UL/CSA certified main circuit breaker,
delay fuses and bases)
|
|
| OPC00763 |
-Mexico (includes labels and technical documentation
in Spanish) |
|
| X41731 |
-Status indicator light |
|
| OPC00764 |
-Parts Warranty from 12 to 24 months after machine delivery |
|
| OPE00033 |
-Bar guide tube, with nylon disks for bar diameter |
|
| OPE01011 |
-Blind disk kit (5 blind disks & 1 flange) to be
prepared by customer
|
|
| |
Following 4 items and the Spindle Orientation option are necessary for driven tools |
|
| S65679 |
Ladder Logic |
|
| S75371 |
Live tool holder (does not include live tool) |
|
| X42960 |
Live tool interface |
|
| X44372 |
72 position index |
|
| |
Note: Maximum diameter using disks
is 1 3/8” 16C Collets,
Round Hex and
Square are available from Lyndex
Additional Tooling (Set of 7 holders and 5
sleeves are standard, see above) |
S65183-Mechanical bar puller w/built in cutoff
tool holder - 3/4 X 3/4”
S65170-Cut-off tool holder - 3/4
X 3/4”
S65111-Turning & Facing holder, bi-directional - 3/4 X 3/4”
S65079-Boring bar holder - 1”
S65077-Double Boring bar holder – 1”
R86805-Reduction sleeve 5/16” x 1”
R86806-Reduction sleeve 3/8” x 1“
R86807-Reduction sleeve 1/2” x 1“
R86808-Reduction sleeve 5/8” x 1“
R86809-Reduction sleeve 3/4” x 1“
R86811-Drill socket MT-1 x 1“
X43488-Boring bar holder with through the tool coolant 1 1/4” Requires
X40319
S65075-Reduction sleeve 3/8” x 1 1/4“
S65074-Reduction sleeve 1/2” x 1 1/4“
S65073-Reduction sleeve 5/8” x 1 1/4“
S65071-Reduction sleeve 3/4” x 1 1/4“
S65068-Reduction sleeve 1” x 1 1/4“
|
|
| |
