D1-8” Spindle Bore:                                  

Spindle Speeds (18)                           

Swing over Bed:                                          

Swing over Cross Slide                          

Cross Slide Travel                                      

Top Slide Travel                                        

Bed Length-Longitudinal Travel           

 Spindle Horsepower                                     

The headstock gears are alloy (Cr,Ni,Mo) steel, hardened and ground using Reishauer electronic gear grinders

The D1-8” Camlock spindle utilizes high precision, individually lubricated, Timken roller bearings

Oil bath lubrication prevents overheating and bearing failure

Spindle Center4 MT, Taper 1:20

The large drive gear is located close to the spindle nose

Single multi-ribbed vee belt to connect drive motor to headstock

The end gear door locks, and there is a safety disconnect when door opens

End gear set (steel) for 184 threads.

Inch, diametral pitch, metric and module threads can be cut with standard quadrant gear set

46 Inch threads can be cut with standard quadrant set from 4 to 36 TPI, includes 32 TPI.

BED

Optional: Gap Bed with bridge, well ribbed, with extra depth

Precision hardened and ground ways

Bed ways are induction hardened to >45  Rc

All way surfaces are ground in one set-up

Full length rear splash guard

Coolant system

Chip pan pulls out to the front so the lathe can be placed close to a wall

One shot lubrication system for bed and cross slide guideways

Prepared for the addition of a taper attachment in the field

CARRIAGE AND APRON

Large, easy to read, Inch/Metric dials

Automatic longitudinal disengagement, 4 position stop

Lead screw with Romi’s exclusive backlash elimination feature

Mechanical safety clutch on lead screw and shear pin on the feed rod to prevent serious damage if an accident occurs

Duplicate Emergency Stop Button on the Apron

Forward, reverse and stop control from apron lever

Thread chasing dial for inch or metric threads

Longitudinal feeds (20) with each set of end gears .0013 IPR to .2351 IPR

Cross feeds (20) with each set of end gears .0008 IPR to .1384

TAILSTOCK

Two piece for easy adjustment of taper

Quill Travel 6 11/16”

Quill Diameter 2 3/8”

Quill Morse Taper 4 MT

Quill graduated Inch/Metric

Tang Stop and Tool Knockout

STANDARD EQUIPMENT

• Chuck guard
• Two 4 MT dead centers
• Set of wrenches for machine operation
• Set of leveling screws and nuts
• Set of operation and parts manuals in English
• Electrical system for connection to 230V, 3 phase, 60 Hz
• 115V emergency stop button and control push buttons

Romi T 20 X 60 ”	Price On Request
Romi T 20 X80”	Price On Request
Romi T 20 X 120”	Price On Request
Romi T 20 X 160”	Price On Request

FOB Erlanger, Kentucky

Terms of Payment are 20% with order
Balance due 30 days after shipment
Terms are subject to credit approval by Romi Machine Tools, Ltd.

View Romi Warranty

Machine Accessories
X13148	Automatic Cross Feed Disengagement Note: Cannot be used with DRO
X10989	Romi Drive Plate 11 ” diameter
X13154	Romi T slotted Face Plate 15” diameter
X11707	Micrometer Carriage Stop (0.001”) graduations
X26746	Follow Rest with Bronze Tips 5/16-2” capacity
X13573	Steady Rest Open with Bronze Tips 5/16-3 1/8” capacity
X29655	Steady Rest Closed with Bronze tips 5/16-3 1/8” capacity
X27858	Additional set of bronze tips for Closed 3 1/8”- 6”capacity
X27885	Set of Rollers for Closed 5/16- 3 1/8” capacity
X27884	Set of Rollers for Closed 3 1/8- 6”” capacity
00113	work light
X15318	Taper Turning Attachment 13 3/4” turning length 15 degree maximum angle
S08541	Extra set of Operation and Parts Manuals Electrics for 440V480Vor 600V Metric Only Version – Special Order Price Reduction for Straight Bed –Special Order
Live Center
10854	4 MT Live Center .0001” TIR
Tool Posts
X13155	Open Sided rear tool post with fixed base
X12764	Square 4 position Tool Post w/Swivel base
SDN40CA	Dorian Super Quick Change Tool Post Set Includes
2-D40CA1	Turn/Face Holder 1-D40CAN-2 Turn/Face/Bore Holder
1-D40CA-4	Boring Bar Holder 1-D40CA-7-71C Cutoff Holder
QITP40N	Dorian Quadra Tool Post Set Includes
2-QITP40N-1	Turn/Face Holder 1-QITP40N-2 Turn/Face/Bore Holder
1-QITP40N-4	Boring Bar Holder 1-QITP40N-7-71C Cutoff Holder
Digital Readouts
ACURITE DRO 200 T, Installed	NEWALL C 80 Microsyn/Spherosyn
Romi T 20 X 60”
Romi T 20 X 80”
Romi T 20 X 120”
Romi T 20 X 160”
Work Holding
	Note: Bison Chucks are available, but are sold without warranty
Atlas 10”	3-Jaw Easy-Set Semi Steel Body Chuck with D1 mounting plate and two piece jaws
Atlas 12”	3-Jaw Easy-Set Semi Steel Body Chuck with D1 mounting plate and two piece jaws
Atlas 15”	3-Jaw Easy-Set Semi Steel Body Chuck with D1 mounting Plate and two piece jaws
PB51008	PBA 10 ” 3-Jaw Setrite Steel Body Chuck with D1 mounting Plate and two piece jaws
PB51208	PBA 12 ” 3-Jaw Setrite Steel Body Chuck with D1 mounting Plate and two piece jaws
PB51508	PBA 15 ” 3-Jaw Setrite Steel Body Chuck with D1 mounting Plate and two piece jaws
158157	Rohm 3- Jaw 10” Scroll Chuck Steel Body with mounting plate and reversible top jaws
Manual 4 Jaw Chucks
Atlas 12”	4-Jaw Direct Mount Cast Iron Body Chuck with solid reversible jaws
Atlas 16”	4-Jaw Direct Mount Cast Iron Body Chuck with solid reversible jaws
12144	PBA 12” 4-Jaw Direct Mount Cast Iron Body Chuck direct mount with solid reversible jaws
14145	PBA 14” 4-Jaw Direct Mount Cast Iron Body Chuck direct mount with solid reversible jaws
16145	PBA 16” 4-Jaw Direct Mount Cast Iron Body Chuck direct mount with solid reversible jaws